Pasito 1.0 Outdoor step lights for lighting walkways - L&L Luce&Light

Pasito 1.0

step light for outdoor applications - 10W 230Vac / 8,5W 24Vdc

recessed mounted, flush

Technical data

Print technical data

Required outer casing not included

230Vac
24Vdc
kg 0,49
IP65
IK07

Installation	step light for outdoor applications
Power consumption	10W (230Vac), 8.5W (24Vdc)
Power supply	230Vac, 24Vdc
Lumen output at source	788 lm (3000K, CRI >90), 851 lm (3000K, CRI 80)
Delivered lumen output	296 lm (3000K, 60°, CRI >90, white finish), 320 lm (3000K, 60°, CRI 80, white finish), 361 lm (3000K, 150°x90° asymmetrical, CRI >90, white finish), 390 lm (3000K, 150°x90° asymmetrical, CRI 80, white finish)
Datasheet	Pasito 1.0 step light for outdoor applications; Awards: German Design Award 2018; recessed, flush (wall); Power consumption: 10W (230Vac), 8.5W (24Vdc); Power supply: 230Vac, 24Vdc; Lumen output at source: 788 lm (3000K, CRI >90), 851 lm (3000K, CRI 80); Delivered lumen output: 296 lm (3000K, 60°, CRI >90, white finish), 320 lm (3000K, 60°, CRI 80, white finish), 361 lm (3000K, 150°x90° asymmetrical, CRI >90, white finish), 390 lm (3000K, 150°x90° asymmetrical, CRI 80, white finish); 1 high-intensity power LED, 3-step MacAdam, 50 000h L90 B10 (Ta 25°C); LED colour: 2700K, 3000K, 4000K; Optics: 60°: optical system consisting of a 60° hemispherical lens, installed at an angle and set back in the chamber to to create a controlled downward light beam, reducing light spill to a minimum, asymmetrical 150°x90°: optical system consisting of an asymmetrical hemispherical lens, installed at an angle and set back in the chamber to to create a controlled downward light beam, reducing light spill to a minimum; Upward flux fraction: 14,72% (asymmetrical 150°x90°, white, grey finish), 1,49% (asymmetrical 150°x90°, cor-ten, anthracite finish), 13,44% (60°, white, grey finish) , 1,76% (60°, cor-ten, anthracite finish); CRI Colour Rendering Index: 80, >90; Body material: body made of ANTICORODAL 6060 low-copper-content aluminium alloy, made from an extruded profile, then anodized black to give the product better heat dissipation and increase its resistance to corrosion. Structured reflector made of extruded ANTICORODAL 6060 aluminium, painted in the same colour; Finishes: white finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector (RAL 9003), grey finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector (RAL 9006), cor-ten finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector, anthracite finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector; RAL finish on request; 230Vac: power supply unit included, 24Vdc: power supply unit not included; 230Vac version: includes 0,20 m neoprene cable, H05RN-F 2x1,0 Ø7 mm; 24Vdc version: includes 0,30 m neoprene cable, H05RN-F 2x0,35/0,75 Ø6,3 mm; Ingress protection: IP65; Impact resistance: IK07; Protection systems: IPS (Intelligent Protection System) protects lighting fixtures from water infiltrations, which can occur if there are faulty junctions between the cables in outdoor or underwater applications. This innovation, patented by L&L, also guarantees electrical protection against polarity reversal, hot plugging, ESD and power surges, which can occur if there are faults in the electrical circuit; Operating temperature: -20°C — +45°C; Photobiological safety: photobiological safety: risk group 1 according to EN 62471:2006; Appliance class: class II (230Vac), class III (24Vdc); Weight: 490 g; Dimensions: 143x67x161 mm; Cutout dimensions: 143x161 mm; Energy efficiency class: A / A+ / A++ (integrated LED module) in accordance with UE 874/2012; Accessories: WC1410E Outer casing - white, WC1410F Outer casing - grey, WC1410H Outer casing - anthracite, WC1410T Outer casing - cor-ten; tested and approved via E.O.L. (End Of Line) test with functioning test and check of electrical power consumptionPasito 1.0 step light for outdoor applications Awards: German Design Award 2018 recessed, flush (wall) Power consumption: 10W (230Vac), 8.5W (24Vdc) Power supply: 230Vac, 24Vdc Lumen output at source: 788 lm (3000K, CRI >90), 851 lm (3000K, CRI 80) Delivered lumen output: 296 lm (3000K, 60°, CRI >90, white finish), 320 lm (3000K, 60°, CRI 80, white finish), 361 lm (3000K, 150°x90° asymmetrical, CRI >90, white finish), 390 lm (3000K, 150°x90° asymmetrical, CRI 80, white finish) 1 high-intensity power LED, 3-step MacAdam, 50 000h L90 B10 (Ta 25°C) LED colour: 2700K, 3000K, 4000K Optics: 60°: optical system consisting of a 60° hemispherical lens, installed at an angle and set back in the chamber to to create a controlled downward light beam, reducing light spill to a minimum, asymmetrical 150°x90°: optical system consisting of an asymmetrical hemispherical lens, installed at an angle and set back in the chamber to to create a controlled downward light beam, reducing light spill to a minimum Upward flux fraction: 14,72% (asymmetrical 150°x90°, white, grey finish), 1,49% (asymmetrical 150°x90°, cor-ten, anthracite finish), 13,44% (60°, white, grey finish) , 1,76% (60°, cor-ten, anthracite finish) CRI Colour Rendering Index: 80, >90 Body material: body made of ANTICORODAL 6060 low-copper-content aluminium alloy, made from an extruded profile, then anodized black to give the product better heat dissipation and increase its resistance to corrosion. Structured reflector made of extruded ANTICORODAL 6060 aluminium, painted in the same colour Finishes: white finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector (RAL 9003), grey finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector (RAL 9006), cor-ten finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector, anthracite finish obtained through an initial treatment of the material with ALODINE NT-E®, followed by a coat of epoxy paint and one of POLYESTER paint to provide corrosion resistance of more than 1500 hours of salt spray. Paints compliant with the Qualicoat standard used in the automotive sector RAL finish on request 230Vac: power supply unit included, 24Vdc: power supply unit not included 230Vac version: includes 0,20 m neoprene cable, H05RN-F 2x1,0 Ø7 mm; 24Vdc version: includes 0,30 m neoprene cable, H05RN-F 2x0,35/0,75 Ø6,3 mm Ingress protection: IP65 Impact resistance: IK07 Protection systems: IPS (Intelligent Protection System) protects lighting fixtures from water infiltrations, which can occur if there are faulty junctions between the cables in outdoor or underwater applications. This innovation, patented by L&L, also guarantees electrical protection against polarity reversal, hot plugging, ESD and power surges, which can occur if there are faults in the electrical circuit Operating temperature: -20°C — +45°C Photobiological safety: photobiological safety: risk group 1 according to EN 62471:2006 Appliance class: class II (230Vac), class III (24Vdc) Weight: 490 g Dimensions: 143x67x161 mm Cutout dimensions: 143x161 mm Energy efficiency class: A / A+ / A++ (integrated LED module) in accordance with UE 874/2012 Accessories: WC1410E Outer casing - white, WC1410F Outer casing - grey, WC1410H Outer casing - anthracite, WC1410T Outer casing - cor-ten tested and approved via E.O.L. (End Of Line) test with functioning test and check of electrical power consumption Copied

Mounting	recessed, flush (wall)
Number and type of LED	1 high-intensity power LED, 3-step MacAdam, 50 000h L90 B10 (Ta 25°C)
LED colour	2700K, 3000K, 4000K
Optics	60°, asymmetrical 150°x90°
CRI Colour Rendering Index	80, >90
Body material	body in anticorodal aluminium
Finishes	white, grey, cor-ten, anthracite
Power supply unit	230Vac: power supply unit included, 24Vdc: power supply unit not included
Power cables	230Vac version: includes 0,20 m neoprene cable, H05RN-F 2x1,0 Ø7 mm; 24Vdc version: includes 0,30 m neoprene cable, H05RN-F 2x0,35/0,75 Ø6,3 mm
Ingress protection	IP65
Impact resistance	IK07
Status	Available

Read more

Close

Download

See all downloads

Gallery

Accessories and power supply units

Accessories (4)

Outer casings

Required outer casing not included WC1410E Outer casing - white	Required outer casing not included WC1410F Outer casing - grey
Required outer casing not included WC1410H Outer casing - anthracite	Required outer casing not included WC1410T Outer casing - cor-ten

Power supply units (15)

ACUNI020T1

ON/OFF constant-current PSU

Input	230Vac 50-60 Hz
Output	24Vdc; 16W 250mA constant current; max 13W 350mA constant current; max 19W 400mA constant current; max 20W 450mA constant current; max 20W 500mA constant current; max 20W 550mA constant current; max 20W 600mA constant current; max 20W 700mA constant current; max 20W
Dimmering	Cannot be dimmed
Power supply unit IP	IP20

ACUNI032T1

ON/OFF constant-current PSU

Input	230Vac 50-60 Hz
Output	24Vdc; 20W 12Vdc; 10W 28Vdc; 22W 350mA constant current; max 17W 500mA constant current; max 24W 550mA constant current; max 25W 700mA constant current; max 32W
Dimmering	Cannot be dimmed
Power supply unit IP	IP20

AD020DALIT1

DALI dimmable power supply unit

Output	24Vdc; 16W 250mA constant current; max 10W 350mA constant current; max 15W 400mA constant current; max 17W 450mA constant current; max 19W 500mA constant current; max 20W 550mA constant current; max 20W 600mA constant current; max 20W 700mA constant current; max 20W
Dimmering	DALI, ON/OFF
Power supply unit IP	IP20

AD032TLT1

Dimmable power supply unit

Input	230Vac 50-60 Hz
Output	24Vdc; 20W 12Vdc; 10W 28Vdc; 22W 350mA constant current; max 17W 500mA constant current; max 24W 550mA constant current; max 25W 700mA constant current; max 32W 750mA constant current; max 32W
Dimmering	PUSH, Mains dimming, ON/OFF
Power supply unit IP	IP20

ADUNITC

1-10V+PUSH dimmable power supply unit

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 20W 12Vdc; 11W 250mA constant current; max 13W 300mA constant current; max 16W 350mA constant current; max 18W 400mA constant current; max 21W 450mA constant current; max 23W 500mA constant current; max 25W 550mA constant current; max 27W 600mA constant current; max 30W 650mA constant current; max 32W 700mA constant current; max 32W 750mA constant current; max 20W 800mA constant current; max 20W 850mA constant current; max 20W 900mA constant current; max 20W
Dimmering	0/1-10V, PUSH, ON/OFF
Power supply unit IP	IP20

AV24010IP20

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 10W
Dimmering	ON/OFF
Power supply unit IP	IP20

AV24020IP67

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 20W
Dimmering	ON/OFF
Power supply unit IP	IP67

AV24040IP67

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 40W
Dimmering	ON/OFF
Power supply unit IP	IP67

AV24060IP20

ON/OFF constant-voltage PSU

Input	230Vac 50-60 Hz
Output	24Vdc; 60W
Dimmering	ON/OFF
Power supply unit IP	IP20

AV24060IP67

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 60W
Dimmering	ON/OFF
Power supply unit IP	IP67

AV24100IP20

ON/OFF constant-voltage PSU

Input	230Vac 50-60 Hz
Output	24Vdc; 100W
Dimmering	ON/OFF
Power supply unit IP	IP20

AV24150IP20

ON/OFF constant-voltage PSU

Input	230Vac 50-60 Hz
Output	24Vdc; 150W
Power	150W
Dimmering	ON/OFF
Power supply unit IP	IP20

AV24150IP67

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 150W
Dimmering	ON/OFF
Power supply unit IP	IP67

AV24240IP67

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 240W
Dimmering	ON/OFF
Power supply unit IP	IP67

AV24320IP67

ON/OFF constant-voltage PSU

Input	115-230Vac 50-60 Hz 230Vac 50-60 Hz
Output	24Vdc; 320W
Dimmering	ON/OFF
Power supply unit IP	IP67

Control gear (1)

ADV576DALIN1

Low-voltage dimmer

order in addition to PSU

Input	12-24-48Vdc
Output	With 24 Vdc input:; 24Vdc; 288W With 12 Vdc input:; 12Vdc; 144W With 48 Vdc input:; 48Vdc; 576W
Dimmering	0/1-10V, PUSH, DALI, 10kΩ potentiometer
Power supply unit IP	IP20

Control input (4)

AE01350T1

Emergency module integrated

Input	220─240Vac 50─60Hz
Output	max 350mA 58Vdc max
Ingress protection	IP20
Dimensions	35x47x166 mm, 185 g
Cutout dimensions	Ø58 mm

TLC05

Radio control with 4 channels

Input	1 x 12V alkaline battery
Output	433,90 MHz
Ingress protection	IP20
Dimensions	Ø85x28 mm

TLC06

Radio control with 2 channels

Input	1 x 3V CR2025 battery
Output	433,90 MHz
Ingress protection	IP20
Dimensions	55x28x10 mm

TLR01

Receiver required for TLC05 and TLC06 remote control

Input	12─24Vdc
Output	2 clean contacts
Ingress protection	IP20
Dimensions	90x53x28 mm

Projects

Entertainment
L&L stand - Light+Building 2018
Frankfurt am Main, Germany

Versions